LEVELLING & FILLING LAYER OF SOLAR ROAD
In the new energy town of Tongli, Suzhou, there is a magical road. The vehicle driving through is not only unmanned, but also can be charged while driving. This is the world’s first 3-in-1 solar road, integrated photovoltaic road, wireless charging and unmanned driving into one transport environment. In addition to the above functions, it can melt snow and ice, provide traffic signages etc. So it is called "a smart highway without power outages".
This solar highway requires very high performance paving materials. Apart from bearing the heavy traffic loads, it also requires high transparency to ensure power generation efficiency. with its high performance, high strength and high transmittance, Bond Materials’ innovative cold-mix epoxy asphalt becomes the ideal solution for solar road pavement.
PRODUCT OVERVIEW
CoolBondTM Epoxy Asphalt is a two-component outdoor epoxy series product developed by Bond Materials Co Ltd in cooperation with Bonding Technology Australia Pty Ltd. The product is asphalt modified epoxy cement. The A/B component must be used according to the ratio specified on the technical datasheet to achieve the best performance. The product has the characteristics of both epoxy and asphalt, suitable for the bottom layer filling and thin coating of photovoltaic pavement. Functional pavement such as anti-skid and wear-resistant pavement.
PRODUCT CHARACTERISTICS
1. High bonding strength. Excellent adhesion to asphalt and concrete surface.
2. Excellent characteristics of both epoxy and asphalt. Water and corrosion resistant. Weather resistant.
3. Low cost.
PRODUCTS
APPLICATION GUIDE
1. Clean the application surfaces thoroughly.
2. Add the main product and curing agent into a container at the ratio specified in the product datasheet. Mix evenly for 2 to 3 minute. Avoid generating bubbles.
3. Apply the mixture to the designated surface within its open time
4. Clean the remaining mixture in the container once finish using it.
5. This product cannot be mixed with any other products.
TECHNICAL PARAMETERS
| Component | Appearance | Density | Viscosity (25ºC, CPS) | Gel Time @25ºC (min) |
Initial Curing Time @25ºC (min) |
Mixing Ratio |
| Part A | Black liquid | 1.46 | 12000-15000 | 25 – 30 | 100 – 120 | 2 |
| Part B | Black liquid | 1.02 | 1000–1200 |
|
|
1 |
Physical properties of the product after curing：
| A/B component ratio： | 2.0:1.0 | 1.5:1.0 | 1.3:1.0 | 1.0:1.0 |
| Tensile Strength（Mpa）： | 18.2 | 6.8 | 4.7 | 2.1 |
| Elongation（%）： | 38 | 108 | 158 | 230 |
| Shore D hardness： | 70 | 55 | 32 | 10 |
| Marshall stability(KN)： | 86.3 | 75.5 | 50.6 | 30.1 |
| Anti-rutting stability（times/mm）： | No deformation | >70000 | >70000 | 63000 |
| Applications： |
HFS Ultra-thin anti-skid surfacing |
Semi-rigid anti-rutting wear-resistant Wear Layer |
Large steel bridge deck structure layer, surface layer | Flexible pavement structure layer, surface layer |
LEVELLING & FILLING LAYER OF SOLAR ROAD
In the new energy town of Tongli, Suzhou, there is a magical road. The vehicle driving through is not only unmanned, but also can be charged while driving. This is the world’s first 3-in-1 solar road, integrated photovoltaic road, wireless charging and unmanned driving into one transport environment. In addition to the above functions, it can melt snow and ice, provide traffic signages etc. So it is called "a smart highway without power outages".
This solar highway requires very high performance paving materials. Apart from bearing the heavy traffic loads, it also requires high transparency to ensure power generation efficiency. with its high performance, high strength and high transmittance, Bond Materials’ innovative cold-mix epoxy asphalt becomes the ideal solution for solar road pavement.
PRODUCT OVERVIEW
CoolBondTM Epoxy Asphalt is a two-component outdoor epoxy series product developed by Bond Materials Co Ltd in cooperation with Bonding Technology Australia Pty Ltd. The product is asphalt modified epoxy cement. The A/B component must be used according to the ratio specified on the technical datasheet to achieve the best performance. The product has the characteristics of both epoxy and asphalt, suitable for the bottom layer filling and thin coating of photovoltaic pavement. Functional pavement such as anti-skid and wear-resistant pavement.
PRODUCT CHARACTERISTICS
1. High bonding strength. Excellent adhesion to asphalt and concrete surface.
2. Excellent characteristics of both epoxy and asphalt. Water and corrosion resistant. Weather resistant.
3. Low cost.
PRODUCTS
APPLICATION GUIDE
1. Clean the application surfaces thoroughly.
2. Add the main product and curing agent into a container at the ratio specified in the product datasheet. Mix evenly for 2 to 3 minute. Avoid generating bubbles.
3. Apply the mixture to the designated surface within its open time
4. Clean the remaining mixture in the container once finish using it.
5. This product cannot be mixed with any other products.
TECHNICAL PARAMETERS
| Component | Appearance | Density | Viscosity (25ºC, CPS) | Gel Time @25ºC (min) |
Initial Curing Time @25ºC (min) |
Mixing Ratio |
| Part A | Black liquid | 1.46 | 12000-15000 | 25 – 30 | 100 – 120 | 2 |
| Part B | Black liquid | 1.02 | 1000–1200 |
|
|
1 |
Physical properties of the product after curing：
| A/B component ratio： | 2.0:1.0 | 1.5:1.0 | 1.3:1.0 | 1.0:1.0 |
| Tensile Strength（Mpa）： | 18.2 | 6.8 | 4.7 | 2.1 |
| Elongation（%）： | 38 | 108 | 158 | 230 |
| Shore D hardness： | 70 | 55 | 32 | 10 |
| Marshall stability(KN)： | 86.3 | 75.5 | 50.6 | 30.1 |
| Anti-rutting stability（times/mm）： | No deformation | >70000 | >70000 | 63000 |
| Applications： |
HFS Ultra-thin anti-skid surfacing |
Semi-rigid anti-rutting wear-resistant Wear Layer |
Large steel bridge deck structure layer, surface layer | Flexible pavement structure layer, surface layer |
Service Hotline：400 825 1528
Phone：+86-20-82210601
Fax：+86-20-82210626
Mailbox：sales@gzthebond.com
